Key takeaways
- Compare the best snowmobile heated grips for cold trail rides, from 12V heater kits and clamp-on grips to waterproof wrap-around warmers for winter.
Cold hands change a snowmobile ride in a hurry. When fingers stiffen, throttle control feels less precise, braking takes more effort, and a long trail day can end earlier than planned. Heated grips warm the palms where they meet the handlebars, so riders can keep a relaxed grip and stay focused on the trail ahead.
The best snowmobile heated grips for most riders balance steady heat, simple controls, a secure fit on common handlebar sizes, and weather sealing that stands up to snow, slush, and spray. Some kits replace the grips, others add elements beneath the existing grips, and covers fit over them.
As an Amazon Associate, we earn from qualifying purchases.
Quick Answer
For a simple budget starting point, choose the Kimpex 30W Handlebar Grip Heater Kit, which adds high and low heat beneath existing grips. For a complete replacement grip, look at the Heat Demon 215049 clamp-on kit and the Koso Apollo heated grips. The SOBMOTO 12V heated grip wraps suit riders who want a removable cover, while the KEMIMOTO 12V heated grip pads suit riders who want a wrap-style pad with three heat levels and waterproof construction.
Table of Contents
- Quick Answer
- How to Choose Snowmobile Heated Grips
- 1. Kimpex 30W Handlebar Grip Heater Kit
- 2. Heat Demon 215049 Clamp-On Heated Grip Kit
- 3. Koso Apollo Heated Grips
- 4. SOBMOTO 12V Heated Grip Wraps
- 5. KEMIMOTO 12V Heated Grip Pads
- How the Five Picks Compare
- Frequently Asked Questions
- Conclusion
- Product and ASIN Reference
How to Choose Snowmobile Heated Grips
Start with fit. Most kits in this guide are built around 7/8 inch handlebars, which are common on snowmobiles, while the Koso Apollo set also covers 1 inch bars. Measure the handlebar diameter before ordering, and check whether the kit replaces the grips, heats beneath them, or wraps over them.
Next, look at heat control and power. A simple high and low switch is easy to use with thick gloves. More levels give finer control when the temperature changes through the day. Most snowmobile heated grips run from the sled electrical system, so check the listed voltage and wattage, plan the wire route so cables stay clear of steering movement, and keep connectors away from standing water. A low-voltage cut-off can switch the heaters off before the battery drops too far to start the engine.
Weather protection matters too. Sealed switches and water-resistant materials cope better with snow and slush. Heated grips warm the palm, while the back of the hand relies on the glove and on handguards or handlebar mitts.
1. Kimpex 30W Handlebar Grip Heater Kit
The Kimpex 30W Handlebar Grip Heater Kit adds electric heat without changing the grips already on the sled. The heating elements fit beneath the existing grips, so the shape, texture, and diameter of the current grips stay the same. That makes it a practical option for riders who like their present grips.
The kit is listed at 30 watts, with high and low heat levels. Adhesive mounting holds the elements in place under the grips and keeps the installation neat. The listed voltage is 14 volts, which matches the charging voltage found on many snowmobile electrical systems when the engine is running. The kit is widely listed for snowmobile use.
Best for: riders who want to keep their current grips and add simple high and low heat.
Keep in mind: the grips must be removed and refitted during installation, so fitting takes more care than slipping on a wrap.
Specs
| Feature | Detail |
|---|---|
| Product | Kimpex 30W Handlebar Grip Heater Kit |
| Model | 12-170 |
| Power | 30 watts |
| Heat levels | High and low |
| Voltage | 14 volts |
| Mounting | Adhesive heating elements under existing grips |
| Fit | Snowmobile and ATV handlebars |
| Brand | Kimpex |
2. Heat Demon 215049 Clamp-On Heated Grip Kit
The Heat Demon 215049 is a complete clamp-on heated grip kit, so it replaces the grips rather than heating beneath them. That gives the rider a fresh grip surface as well as built-in heat, which is useful when the original grips are worn, slippery, or uncomfortable in cold weather. The rubber grip material is listed in the Amazon product details, and the kit is sized for 7/8 inch handlebars.
Control is handled by a round rocker switch with high, low, and off positions. The round shape is easy to find and operate with a gloved hand. The kit is listed with a maximum of 20 watts per grip at 14 volts, which gives a clear picture of the electrical load for planning the sled connection. The kit is listed as fitting most all-terrain vehicles and snowmobiles.
Best for: riders who want a full replacement grip with a simple round rocker switch and clamp-on fitting.
Keep in mind: the kit is sized for 7/8 inch bars, so riders with a different bar diameter should measure first.
Specs
| Feature | Detail |
|---|---|
| Product | Heat Demon 215049 Clamp-On Heated Grip Kit |
| Model | 215049 |
| Heat levels | High, low, and off |
| Switch | Round rocker switch |
| Power | Maximum 20 watts per grip at 14 volts |
| Grip material | Rubber |
| Handlebar size | 7/8 inch |
| Item weight | 8.9 ounces |
| Fit | Most ATVs and snowmobiles |
| Brand | Heat Demon |
3. Koso Apollo Heated Grips
The Koso Apollo heated grips are the premium pick in this guide, aimed at riders who want more control and more feedback from the grip itself. The grips are made for 7/8 inch and 1 inch handlebars, which covers a wider range of sleds than a 7/8 inch only kit. The Amazon listing names the material as plastic and rubber.
Its integrated adjustable switch is built into the grip. The Amazon product description explains that the switch lets the rider adjust the temperature level without removing a hand from the handlebar. A five-colour light display shows the heat level at a glance, so the rider can confirm the setting with a quick look. The description also notes a wide temperature setting range for cold riding conditions.
The Koso listing also describes low-voltage battery protection, which switches the grips off when battery voltage drops, so enough power remains to start the engine. The listed item weight is 1.1 pounds, and the model number is AM111030.
Best for: riders who want integrated controls, a visible heat-level display, and low-voltage battery protection.
Keep in mind: the grip shape and the built-in switch change the feel of the bars, so check the dimensions and the switch position before ordering.
Specs
| Feature | Detail |
|---|---|
| Product | Koso Apollo Heated Grips |
| Model | AM111030 |
| Handlebar size | 7/8 inch and 1 inch |
| Control | Integrated adjustable switch |
| Display | Five-colour light display for heat level |
| Battery protection | Low-voltage cut-off described in listing |
| Grip material | Plastic and rubber |
| Item weight | 1.1 pounds |
| Brand | Koso |
4. SOBMOTO 12V Heated Grip Wraps
The SOBMOTO 12V Heated Grip Wraps are wrap-around covers that fit over the grips already on the sled, so the rider keeps the existing grip shape and adds a heated layer on the outside. That design suits riders who want heat for the coldest part of the season and may want to remove the wraps when conditions improve.
The wraps run from a 12 volt supply, either direct from the battery or from an accessory circuit, according to the Amazon listing. Three heat levels give low, medium, and high settings, a useful middle ground between a simple two-level switch and a more complex controller. The wraps are rated IP67 waterproof.
Fit is defined by the outer diameter of the existing grips. The listing states that the wraps fit grips with an outer diameter from 1.2 inches to 1.5 inches, so riders should measure the grips before ordering. The listing names snowmobiles among the vehicle types, alongside motorcycles, all-terrain vehicles, dirt bikes, and scooters.
Best for: riders who want a removable, waterproof wrap with three heat levels and no grip replacement.
Keep in mind: measure the outer diameter of the current grips first, because the 1.2 inch to 1.5 inch fit range is the key sizing check.
Specs
| Feature | Detail |
|---|---|
| Product | SOBMOTO 12V Heated Grip Wraps |
| Power source | 12 volt, direct battery or accessory powered |
| Heat levels | 3, low, medium, and high |
| Waterproof rating | IP67 |
| Fit | Grips with 1.2 inch to 1.5 inch outer diameter |
| Design | Wrap-around covers over existing grips |
| Vehicle types | Snowmobiles, motorcycles, ATVs, dirt bikes, and scooters |
| Brand | SOBMOTO |
5. KEMIMOTO 12V Heated Grip Pads
The KEMIMOTO 12V Heated Grip Pads are heating pads that fit over the handlebar grips. The Amazon listing describes them as heated grip pads for 12 volt all-terrain vehicle and motorcycle use, with a universal fit for 0.86 inch diameter handlebars, which is the same as 22 millimetres. That size matches many snowmobile bars, but measuring first remains the sensible step.
Three heat levels are controlled by a switch with coloured indicator lights. The Amazon product description explains the light pattern: red for high, blue for medium, and green for low, with the light staying on while the pad is working. That simple colour code is easy to read at a glance, even when the rider is wearing gloves. The listing describes the pads as fast heating, and the product summary names IP67 waterproof construction.
The material is listed as Kevlar and silicone. The pads are fixed with double-sided tape and an L-shaped bracket base, and the pads are removable from the wiring for cleaning. The listed dimensions are 5.3 by 3.9 by 0.1 inches.
Riders should follow the wiring notes in the listing carefully, including the polarity guidance.
Best for: riders who want a removable heated pad with three levels, coloured indicators, and waterproof construction.
Keep in mind: the pads are sized for 0.86 inch bars, so check the handlebar diameter before ordering.
Specs
| Feature | Detail |
|---|---|
| Product | KEMIMOTO 12V Heated Grip Pads |
| Power source | 12 volt |
| Heat levels | 3, high, medium, and low |
| Indicator | Red for high, blue for medium, green for low |
| Waterproof rating | IP67 |
| Material | Kevlar and silicone |
| Handlebar size | 0.86 inch, 22 millimetres |
| Mounting | Double-sided tape and bracket base |
| Dimensions | 5.3 by 3.9 by 0.1 inches |
| Brand | KEMIMOTO |
How the Five Picks Compare
The five picks cover three fitting styles: the Kimpex kit heats beneath the existing grips, the Heat Demon and Koso kits replace them, and the SOBMOTO and KEMIMOTO options wrap over them.
Heat control ranges from two levels on the Kimpex kit to three levels on the SOBMOTO and KEMIMOTO options, with the Heat Demon rocker adding an off position and the Koso Apollo adding an integrated switch and a five-colour display. Weather sealing is strongest on the two wrap options, both rated IP67. In budget terms, the Kimpex kit and the KEMIMOTO pads are the budget picks, the SOBMOTO wraps and the Heat Demon clamp-on kit sit in the mid-range, and the Koso Apollo grips are the premium pick.
Frequently Asked Questions
Do snowmobile heated grips work with thick winter gloves?
Yes, heated grips work with thick winter gloves, but the heat reaches the palm more slowly through heavy insulation. A midweight glove often gives a better balance of warmth and feel. Handlebar mitts or handguards help by blocking wind from the back of the hand, which the grips cannot warm directly.
Are heated grips hard to install on a snowmobile?
Installation difficulty depends on the type. Wrap-around covers are usually the simplest to fit, because they go over the existing grips and connect to a 12 volt supply. Under-grip heater kits need the grips removed and refitted, which takes more time and care. Full replacement grips need the old grips removed and the new grips fitted and wired.
Can heated grips drain a snowmobile battery?
Heated grips draw power from the sled electrical system, so they can drain the battery if they are left on with the engine off. Most riders switch the grips off when the engine stops. The Koso Apollo listing describes a low-voltage cut-off that switches the grips off when battery voltage drops.
What handlebar size do snowmobile heated grips fit?
Most kits in this guide fit 7/8 inch handlebars, which are common on snowmobiles. The Koso Apollo grips also fit 1 inch bars, the KEMIMOTO pads are listed for 0.86 inch bars, and the SOBMOTO wraps are sized by grip outer diameter from 1.2 inches to 1.5 inches. Measure the handlebar diameter and, for wraps, the outer diameter of the grips before ordering.
Conclusion
The best snowmobile heated grips match the sled, the gloves, and the way the rider uses heat. The Kimpex 30W kit is a simple budget starting point for riders who want to keep their current grips. The Heat Demon 215049 clamp-on kit and the Koso Apollo grips suit riders who want a complete replacement, with the Koso set adding integrated controls and battery protection for riders who adjust heat often. The SOBMOTO 12V wraps and the KEMIMOTO 12V pads suit riders who prefer a removable, waterproof layer over the grips they already have.
Before ordering, measure the handlebars, check the sled electrical connection, and choose the heat control that feels easiest to use with gloves on.
FAQ
Do snowmobile heated grips work with thick winter gloves?
Are heated grips hard to install on a snowmobile?
Can heated grips drain a snowmobile battery?
What handlebar size do snowmobile heated grips fit?
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeA free business account with business pricing and bulk-buying tools for work, shop or home office.
Create a business accountAs an Amazon Associate we earn from qualifying purchases.





Write Your Review
No reviews yet. Be the first to share your experience!